How to Replace Rotor for HX Series Sand Maker Accurately
HX system sand machine turned part daughter itself the top edge, center, bottom are wear, shall be made to the equipment suppliers and confirm whether can repair by manufacturer, if cannot repair, need to replace the original factory's daughter.If can repair, the original manufacturers professionals for effective after repair, into the crushing cavity, again after the necessary balance adjustment, can work normally. But do you know how to replace the rotor for HX series sand making machine accurately? If you do not know about it, today our experts will talk about something on it,
1. The ways of tearing down rotor of sand making machine are in the following:
(1) to unload incoming feeder, crusher at the top of the funnel and cloth components. (2) from the clearing points are the center of the stone, and the points are the cloth inside the bolt hole, and then unloaded materials plate bolt after take out the tray.Note: should prevent any drop points are circulated connection thread stone, covered with a cloth. (3) discharge pressure plate bolts and pressure plate.With four bolts lock rotor lifting plate, and in turn the locking bolt until completely locked into and from the rotor locking. Remove the eye bolts on the rotor lift plate up rotor.(lifting plate self-made auxiliary device for the customer)
2, The methods of installing rotor of sand making machine are as follows:
Clean up the shaft turn, lock, locking and daughter raised face, with light oil or dehydrated liquid onto the part surface, and in clean before assembly.In the expansion set of 'top' crack into a small wedge or small screwdriver, make the crack expand slightly.Place up set on the axis, the larger end down, make its strong position in the seal plate.
To unload or with a screwdriver, and remove up set of burrs.The sand making machine rotor lifting plate is installed on the rotor convex, and reducing the rotor to a locking.Before the unload lifting plate, make the lifting plate and up on any other hole hole alignment, unload lifting plate.When the rotor fixed up set, set at the top of the rotor and at least 2 mm distance between the top surface.
Insert the bolts by the pressure plate set and evenly to lock, such expansion can be set up closely to the shaft and rotor surface, then put the bolt locking. Clean up the roof and installation materials plate, using materials plate bolt lock, and the points of material plate bolt hole into cloth, so, can prevent the bolt stone into nearby, so that it is easy to remove.
For more on sand maker: http://chinaquarry.com.
The ways of tearing down rotor of sand making machine : http://www.chinaquarry.com/news_show/n83.html
The methods of installing rotor of sand making machine: http://www.chinaquarry.com/news_show/n100.html
1. The ways of tearing down rotor of sand making machine are in the following:
(1) to unload incoming feeder, crusher at the top of the funnel and cloth components. (2) from the clearing points are the center of the stone, and the points are the cloth inside the bolt hole, and then unloaded materials plate bolt after take out the tray.Note: should prevent any drop points are circulated connection thread stone, covered with a cloth. (3) discharge pressure plate bolts and pressure plate.With four bolts lock rotor lifting plate, and in turn the locking bolt until completely locked into and from the rotor locking. Remove the eye bolts on the rotor lift plate up rotor.(lifting plate self-made auxiliary device for the customer)
2, The methods of installing rotor of sand making machine are as follows:
Clean up the shaft turn, lock, locking and daughter raised face, with light oil or dehydrated liquid onto the part surface, and in clean before assembly.In the expansion set of 'top' crack into a small wedge or small screwdriver, make the crack expand slightly.Place up set on the axis, the larger end down, make its strong position in the seal plate.
To unload or with a screwdriver, and remove up set of burrs.The sand making machine rotor lifting plate is installed on the rotor convex, and reducing the rotor to a locking.Before the unload lifting plate, make the lifting plate and up on any other hole hole alignment, unload lifting plate.When the rotor fixed up set, set at the top of the rotor and at least 2 mm distance between the top surface.
Insert the bolts by the pressure plate set and evenly to lock, such expansion can be set up closely to the shaft and rotor surface, then put the bolt locking. Clean up the roof and installation materials plate, using materials plate bolt lock, and the points of material plate bolt hole into cloth, so, can prevent the bolt stone into nearby, so that it is easy to remove.
For more on sand maker: http://chinaquarry.com.
The ways of tearing down rotor of sand making machine : http://www.chinaquarry.com/news_show/n83.html
The methods of installing rotor of sand making machine: http://www.chinaquarry.com/news_show/n100.html
rabbit231 - 8. Jan, 06:53
